1 General Information

1.1 Document focus

This document describes how to install and commission the eSite x10. It focuses on the installation process of the eSite x10 unit itself and mentions the associated systems only in brief.

The scope of the document covers eSite x10 models RSC-001/1, RC-001/1 and XP-100, see section 1.9 Product numbering for detailed information.

1.2 Target group

This document is intended for personnel that will do the installation and the site commissioning of the eSite x10. All personnel must have sufficient basic skills and training, see section 1.10 Authorization.

1.3 Warning levels

Warning

Highlights hazards that may result in personal injuries and/or serious damage to mechanical structures and equipment.

Caution

Highlights hazards that may result in damage to the equipment.

Note

Highlights general useful information.

Read

Highlights that there is information to read in addition to this document. That information must be considered when operating the device or control.

1.4 Trademarks

eSite™ and eSite Tools™ are registered trademarks of eSite Power Systems AB (publ) and will be referred to hereafter as eSite and eSite Tools.

1.5 Available product documentation

eSite x10 documentation
Product Description
Installation Guide
Operation Manual

1.6 Abbreviations and definitions

1.6.1 Abbreviations

Abbreviation	Description
A	Ampere
Ah	Ampere hour
AC	Alternating Current
ATS	Automatic Transfer Switch
BMS	Battery Monitoring System
BMU	Battery Monitoring Unit
°C	Degree Celsius
CAN	Controller Area Network
CE	Conformité Européenne
DC	Direct Current
EC	European Conformity
EMC	Electromagnetic Compatibility
GND	Electrical Ground
HP	High Priority
Hz	Hertz
kW	Kilowatt
LAN	Local Area Network
LP	Low Priority
MCB	Miniature Circuit Breaker
MPPT	Maximum Power Point Tracker
MHz	Megahertz
N/A	Not Available
NTP	Network Time Protocol
PVC	Polyvinyl chloride
RMS	Remote Monitoring System
SCR	Silicone controlled rectifiers
SoC	State of charge
SIM	Subscriber Identity Module
V	Volt
V AC	AC Volts of Alternating Current
V DC	DC Volts of Direct Current
W	Watt
WLAN	Wireless Local Area Network

1.6.2 Definitions

Definition	Description
Associated systems	The term 'associated systems' refers to parts or systems outside eSite x10, e.g. the battery bank, the genset, the grid and the solar arrays.
Customer load	The customer load is the equipment that is supplied with power from eSite x10.
Tenant	A tenant is a customer whose equipment is part of the customer load. Each tenant may connect equipment as LP and/or HP load. Power consumption may be measured separately for each connected tenant.
Main Compartment	The Main Compartment contains power electronics and the internal control system of eSite x10. The Main Compartment must not be opened.
Connection Compartment	The Connection Compartment is the user point of access to the eSite x10 where all external connections are managed.
Lower Main	The Lower Main is part of the Main Compartment. It is accessed through the Connection compartment when the Main Compartment is docked. Signal cables and control cables are connected to the Lower Main.
eSite Tools	eSite Tools is an RMS that monitors several eSite x10 in a network. eSite Tools can be used to view the status of all connected sites in a network and to create a variety of reports. It can also be used for software upgrades, data downloads and configuration changes.
eSite Web	eSite Web is the eSite x10 web browser interface. It can be reached on-site via the local Ethernet LAN and WLAN networks.

1.7 Compliance

eSite x10 is a carefully designed product that has undergone rigorous performance testing with regards to quality, environment, electrical safety and functionality.

This product and the system software has complied to and met the test standards of:

• ETSI EN 300 386 V1.6.

• ETSI 300 019-1-2 Class 2.

• IEC/EN 60950-1:2005+A1+A11+A12+A2

• IEC/EN 60950-22:2006-A11

1.8 CE-marking

eSite x10 complies to the CE standards. EC (European Conformity) labels are found on both the Main Compartment (see figure 1.1) and the Connection Compartment (see figure 1.2).

Figure 1.1. Product marking plate - Main Compartment

Figure 1.2. Product marking plate - Connection Compartment

1.9 Product numbering

eSite x10 product number (P/N) of the x10 follows the principle:\<Functions>-\<Index>/\<Region> where;

Function: R = Rectifier, S = Solar, I = Inverter, Y = supervision/control generation 1, C = supervision/control generation 2, E = Expansion, X = passive distribution, P = Protection device. Index: New variants of a base product are indicated by an increased Index, where the first version is 001. Region: /1 = Europe, Africa and Asia, /2 = North and South America, the Caribbean and Mexico, /3 = Australia and Islands in the pacific ocean.

Product Number	Description	Comment
RSY-001/1	MC with Solar, Rectifier and supervision/control	Used for main compartment generation 1
RSC-001/1	Main Compartment with Solar, Rectifier and supervision/control	Used for main compartment starting with serial number 7247xxx
RC-001/1	Main Compartment with Rectifier only and supervision/control	Used for main compartment starting with serial number 7250xxx
XP-001	Connection Compartment	Used with main compartment RSY or RSC. Default MCB configuration 3 x 125A, 3 x 32A, 3 x 6A.

1.10 Authorization

Note

Local authorization regulations for work with electrical equipment must always be obeyed.

Warning

All personnel involved must have sufficient competence and training. If not, there is a risk of injury to the personnel and a risk of damage to the equipment.

An unapproved user:

• can work with the eSite only during regular operation.

• can do the first analysis if an alarm operates.

• can log in to eSite Tools or the eSite Web to see information and alarms.

• cannot make changes or configurations in eSite Tools or the eSite Web.

• must not open the Connection Compartment.

An approved user*:

• has the sufficient basic competence that the market requires and has attended an approved eSite training.

• can install the eSite.

• can do site commissioning of the eSite.

• can work with live equipment.

• can replace units.

• can configure the system.

• can do troubleshooting.

*depending on level of training.

1.11 Support

eSite Power Systems operate a 'Service Desk & Knowledge Base', where the Customer can access certain documentation, guides and software, report Issues and request support/resolution of reported Issues.

The Customer may access the 'Service Desk & Knowledge Base' by using a user account (provided by the Supplier). The Service Desk is a single point of contact between the Supplier and the Customer and can be found here:

http://servicedesk.esitepowersystems.com

When reporting Issues or requesting support, the Customer is asked to fill in the appropriate form and describe the problem/request in detail. If applicable, photographs and/or log files may be attached to the request.

Copyright © 2021 eSite Power Systems AB