1 General Information

1.1 Document focus

This document is a description of eSite x10. It focuses on the hardware characteristics and software capabilities. It will also explain how the product works on site with the batteries, genset, grid, solar, and customer load.

1.2 Warning levels

Warning

Highlights hazards that can result in personal injuries. It can also result in serious damage to mechanical structures and equipment.

Caution

Highlights hazards that can result in damage to the equipment.

Note

Highlights general useful information.

Read

Highlights that there is information to read in addition to this document. That information must be considered when operating the device or control.

1.3 Trademarks

eSite™ and eSite Tools™ are registered trademarks of eSite Power Systems AB and will be referred to here after as eSite and eSite Tools.

1.4 Available product documentation

eSite x10 documentation
Product Description
Installation Guide
Operations Manual

1.5 Abbreviations and definitions

Abbreviation	Description
A	Ampere
Ah	Ampere hour
AC	Alternating Current
ATS	Automatic Transfer Switch
°C	Degree Celsius
CAN	Controller Area Network
CE	Conformité Européenne
DC	Direct Current
EC	European Conformity
EMC	Electromagnetic Compatibility
GND	Electrical Ground
HP	High Priority
Hz	Hertz
kW	Kilowatt
LP	Low Priority
MCB	Miniature Circuit Breaker
MPPT	Maximum Power Point Tracker
MHz	Megahertz
N/A	Not Available
NTP	Network Time Protocol
PVC	Polyvinyl chloride
RMS	Remote Monitoring System
SCR	Silicone controlled rectifiers
SOC	State of charge
SIM	Subscriber Identity Module
V	Volt
V	AC Volts of Alternating Current
V	DC Volts of Direct Current
W	Watt
WLAN	Wireless Local Area Network

Definition	Description
Associated systems	The term associated systems refers to parts or systems outside eSite x10, e.g. the battery bank, the genset, the grid and the solar arrays.
Customer load	The customer load is the equipment that is supplied with power from eSite x10.
Main Compartment	The Main Compartment contains power electronics and the control system of eSite x10. The Main Compartment must not be opened.
Connection Compartment	The Connection Compartment is the connection point access to eSite x10.
Lower Main	The Lower Main is part of the Main Compartment. It is reached through the Connection compartment when the Main Compartment is docked. Signal cables and control cables are connected to the Lower Main.
eSite Tools	eSite Tools is an RMS that monitors several eSite x10 in a network. eSite Tools can be used to view the status of all sites in a network and to create a variety of reports. It can also be used for software downloading and for configuration changes.
eSite Web	eSite Web is the eSite x10 interface. It is reached on the site.
Tenant	The tenant is the telecom operator that receives power through eSite x10. Each tenant can connect both high priority load and low priority load. The power consumption can be separately measured for the connected tenants.

1.6 Compliance

eSite x10 is a carefully designed product with performed tests regarding quality, climate, electrical safety, heat and functionality.

This product and the system software has complied to and met the tests standards of:

• ETSI EN 300 386 V1.6.

• ETSI 300 019-1-2 Class 2.

• IEC/EN 60950-1:2005+A1+A11+A12+A

• IEC/EN 60950-22:2006-A

1.7 CE-marking

eSite x10 complies to CE. EC (European Conformity) labels are found on both the Main Compartment (see figure 1.1) and the Connection Compartment (see figure 1.2).

Figure 1.1. Product marking plate - Main Compartment

Figure 1.2. Product marking plate - Connection Compartment

1.8 Product numbering

eSite x10 product number (P/N) of the x10 follows the principle:<Functions>-<Index>/<Region>, where;

Function: R = Rectifier, S = Solar, I = Inverter, Y = supervision/control generation 1, C = supervision/control generation 2, E = Expansion, X = passive distribution, P = Protection device. Index: New variants of a base product are indicated by an increased Index, where the first version is 001. Region: 1 = Europe, Africa and Asia, 2 = North and South America, Caribbean and Mexico, 3 = Australia and Islands in the pacific ocean.

Product_number	Description	Comment
RSY-001/1	MC with Solar, Rectifier and supervision/control	eSite x10 Main Compartment with 10.5 kW rectifier system capacity. eSite x10 Main Compartment with 10.5 kW rectifier system and 6 kW solar power conversion capacity. Used for main compartment generation 1.
RY-001/1	MC with Rectifier only and supervision/control	eSite x10 Main Compartment with 10.5 kW rectifier system capacity. Used for main compartment generation 1
XP-001	Connection Compartment	Used for main compartment generation 1. With the default MCB configuration 3 x 125 A, 3 x 32 A, 3 x 6 A.
XPE-002	Connection Compartment for Expansion units	With site load increase (site load = 9 + 9 kW) Same pre-configuration and available options as for PE-001, but with the possibility to connect 9 kW load also to the expansion CC, with the default MCB configuration 3 x 125 A, 3 x 32 A, 3 x 6 A.
MF-001	Mounting Frame	Frame for mounting the eSite x10.
RE-001/1	Rectifier Expansion	eSite x10 Expansion Unit with 10.5 kW rectifier system capacity.